![]() ![]() On the base unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Many functions can be selected using the touchscreen for added convenience. In addition to the keypad, the FD130 also includes an easy to use touchscreen with a simplified menu. For the second letter on the keyboard, such as B, press twice then. For example, to type the letter A, press then the number 2 key. To enter numbers or letters, simply press the appropriate key. The FD130 has 15 keys that can be used to select numbers, letters, and to enter data. Through the keypad, the user can select transaction types and enter information. In some cases, the device may prompt for a second tap to complete the transaction. The card holder will tap his or her contactless card or device against the contactless icon located on the FD130. The card must remain inserted throughout the entire transaction. Contact your sales or customer service representative.)įind the card reader slot at the front of the FD130 and insert the card completely so the microprocessor chip is no longer visible and the front of the card is facing up. (Optional: Smart card capability must be enabled. Refer to quick reference guide for details. If failure persists, the card's stripe may be damaged, and user will have to manually enter the account number on the keypad.įollow remaining prompts on the display to complete the transaction. If the card swipe fails, check the position of the magnetic stripe and slide the card again. Slide the card in either direction through the slot without stopping. Insert the card into the card reader slot, with the magnetic stripe lying in the slot and facing the terminal. With the idle message displayed, select the desired transaction type. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Use only shielded signal cables to connect I/O devices to this equipment. Please dispose of used battery according to local regulations. Risk of explosion if the battery is replaced by an incorrect type. Plug the adapter into a surge protector (strongly recommended) or a standard 120V electrical outlet.Īdapter spec: LI SHIN INT. The power supply should be the last item connected to the unit. Turn the plug so that cord is directed toward the back of the terminal. Connect the single-pole AC adapter plug to the power input at the right side of the terminal. Not doing so may result in damage to the unit or connected devices.Ĭonnect the power cord to the power supply via the three-prong end and receiver.įind the power input on the right side of the terminal. ![]() If you choose dial-up, you should use a dedicated phone line.īefore using the power supply, please connect all peripherals to the terminal. You may choose an IP connection, (DSL or cable), Wi-Fi or dial-up. Close the cover and tear off any excess paper. The thermal print-side of the paper will feed out facing the operator. Load a roll of paper (Appleton POS Grade Plus 600-2.4 is recommended) into the printer. Pop the printer cover's latch to open the cover then lift the cover. Avoid areas with direct sunlight, objects that radiate heat, excessive dust and other electrical devices that can cause excessive voltage. Place the terminal on a desk or tabletop. Typical set-up time: 10-15 minutes Where to put the FD130 Terminal To connect your power supply to a wall outlet. The USB port cover shall not be removable from other parts of the FIRE ENCLOSURE by the OPERATOR The USB port cover should be kept closed during normal operation. The left is a USB port and the other is a mini USB port. Note: If you open the cover on the bottom of the terminal, you will find two additional ports. You may connect additional peripherals to the USB or COM ports, such as the FD-10, FD-10C or FD35 PIN pads, and/or the MagTek ® MiniMICR Check Reader.įor Internet transactions using Cable or DSL. The ports on the back enable you to add peripherals such as PIN ads, check readers and contactless readers.įor dial-up transactions using a phone line. To prevent damage to the FD Terminals and connected devices, we strongly recommend using a surge protector or UPS (Uninterruptible Power Supply) with a battery backup and phone/fax protection. → Two-piece AC Power Supply What else will you need? ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |